Rack Attack initializer

Overview

Rack Attack, also known as Rack::Attack, is a Ruby gem that is meant to protect GitLab with the ability to customize throttling and to block user IP addresses.

You can prevent brute-force passwords attacks, scrapers, or any other offenders by throttling requests from IP addresses that are making large volumes of requests. If you find throttling is not enough to protect you against abusive clients, Rack Attack offers IP whitelisting, blacklisting, Fail2ban style filtering, and tracking.

For more information on how to use these options see the Rack Attack README.

NOTE: Note: See User and IP rate limits for simpler limits that are configured in the UI.

NOTE: Note: Starting with GitLab 11.2, Rack Attack is disabled by default. If your instance is not exposed to the public internet, it is recommended that you leave Rack Attack disabled.

Behavior

If set up as described in the Settings section below, two behaviors will be enabled:

Protected paths will be throttled.
Failed authentications for Git and container registry requests will trigger a temporary IP ban.

Protected paths throttle

GitLab responds with HTTP status code 429 to POST requests at protected paths that exceed 10 requests per minute per IP address.

By default, protected paths are:

/users/password
/users/sign_in
/api/#{API::API.version}/session.json
/api/#{API::API.version}/session
/users
/users/confirmation
/unsubscribes/
/import/github/personal_access_token
/admin/session

This header is included in responses to blocked requests:

Retry-After: 60

For example, the following are limited to a maximum 10 requests per minute:

User sign-in
User sign-up (if enabled)
User password reset

After 10 requests, the client must wait a minute before it can try again.

Git and container registry failed authentication ban

GitLab responds with HTTP status code 403 for 1 hour, if 30 failed authentication requests were received in a 3-minute period from a single IP address.

This applies only to Git requests and container registry (/jwt/auth) requests (combined).

This limit:

Is reset by requests that authenticate successfully. For example, 29 failed authentication requests followed by 1 successful request, followed by 29 more failed authentication requests would not trigger a ban.
Does not apply to JWT requests authenticated by gitlab-ci-token.

No response headers are provided.

Settings

Omnibus GitLab

Open /etc/gitlab/gitlab.rb with your editor

Add the following:

gitlab_rails['rack_attack_git_basic_auth'] = {
  'enabled' => true,
  'ip_whitelist' => ["127.0.0.1"],
  'maxretry' => 10, # Limit the number of Git HTTP authentication attempts per IP
  'findtime' => 60, # Reset the auth attempt counter per IP after 60 seconds
  'bantime' => 3600 # Ban an IP for one hour (3600s) after too many auth attempts
}

Reconfigure GitLab:
```
sudo gitlab-ctl reconfigure
```

The following settings can be configured:

enabled: By default this is set to false. Set this to true to enable Rack Attack.
ip_whitelist: Whitelist any IPs from being blocked. They must be formatted as strings within a Ruby array. CIDR notation is supported in GitLab v12.1 and up. For example, ["127.0.0.1", "127.0.0.2", "127.0.0.3", "192.168.0.1/24"].
maxretry: The maximum amount of times a request can be made in the specified time.
findtime: The maximum amount of time that failed requests can count against an IP before it's blacklisted (in seconds).
bantime: The total amount of time that a blacklisted IP will be blocked (in seconds).

Installations from source

NOTE: Note: Rack Attack initializer was temporarily renamed to rack_attack_new, to support backwards compatibility with the one Omnibus initializer. It'll be renamed back to rack_attack.rb once Omnibus throttle is removed. Please see the GitLab issue for more information.

These settings can be found in config/initializers/rack_attack.rb. If you are missing config/initializers/rack_attack.rb, the following steps need to be taken in order to enable protection for your GitLab instance:

In config/application.rb find and uncomment the following line:
```
config.middleware.use Rack::Attack
```
Restart GitLab:
```
sudo service gitlab restart
```

If you want more restrictive/relaxed throttle rules, edit config/initializers/rack_attack.rb and change the limit or period values. For example, more relaxed throttle rules will be if you set limit: 3 and period: 1.seconds (this will allow 3 requests per second). You can also add other paths to the protected list by adding to paths_to_be_protected variable. If you change any of these settings you must restart your GitLab instance.

Remove blocked IPs from Rack Attack via Redis

In case you want to remove a blocked IP, follow these steps:

Find the IPs that have been blocked in the production log:

grep "Rack_Attack" /var/log/gitlab/gitlab-rails/auth.log

Since the blacklist is stored in Redis, you need to open up redis-cli:

/opt/gitlab/embedded/bin/redis-cli -s /var/opt/gitlab/redis/redis.socket

You can remove the block using the following syntax, replacing <ip> with the actual IP that is blacklisted:
```
del cache:gitlab:rack::attack:allow2ban:ban:<ip>
```
Confirm that the key with the IP no longer shows up:
```
keys *rack::attack*
```
Optionally, add the IP to the whitelist to prevent it from being blacklisted again (see settings).

Troubleshooting

Rack attack is blacklisting the load balancer

Rack Attack may block your load balancer if all traffic appears to come from the load balancer. In that case, you will need to:

Configure nginx[real_ip_trusted_addresses]. This will keep users' IPs from being listed as the load balancer IPs.
Whitelist the load balancer's IP address(es) in the Rack Attack settings.
Reconfigure GitLab:
```
sudo gitlab-ctl reconfigure
```
Remove the block via Redis.